Plumbing help for Workington homes
Why your boiler pressure keeps dropping, and what to do about it
A boiler that loses pressure once or twice a year is nothing to worry about. A boiler that loses it every week is telling you something.
This guide explains the gauge, the top-up and the hunt for the missing water. It is written for combi boilers and other sealed systems, the kind with a pressure gauge on the front or underneath.
What the gauge is measuring
Your radiators, the pipes that join them and the boiler form one closed loop of water. In a sealed system that water is held under pressure, and the gauge shows how much.
With the heating cold, most boilers want the needle at about 1 to 1.5 bar. Many gauges have a green band to show the right zone. As the water heats it expands, and the needle climbs a little. That is normal.
If the needle drops too low, a safety switch stops the boiler firing. No heating, no hot water, and often a code on the display.
Topping up: fine once, a warning if regular
The filling loop is how water is added. On some boilers it is a braided hose with a valve at each end. On others it is a lever or a key built in underneath. The method differs from one make to the next, so use the instructions for your own boiler. They are usually on a card inside the drop-down flap, and makers publish them online.
The usual pattern is to open the valve slowly, watch the needle rise into the green and shut the valve firmly. Do not walk away while it is open.
After bleeding radiators, a top-up is expected. Once or twice a year is nothing unusual either. More often than that, and the water is going somewhere.
The leak hunt, room by room
You can do the first search yourself with a torch and a sheet of kitchen roll. Do it with the heating on, as some leaks only show when the pipes are hot.
- At every radiator, wipe under both valves and along the bottom seam. Look for rust trails, green or white crust, and stained carpet.
- Follow any pipes you can see, in the airing cupboard, under the stairs and where they rise through floors.
- Check the ceilings below radiators and below the bathroom for marks.
- Go outside and find the small copper pipe that comes through the wall near the boiler and turns down. If it is dripping or the wall is stained under it, note that.
- Look under the boiler itself for drips or a tide mark.
A wet radiator valve is the commonest find, and the cheapest. A UK radiator guide puts taking a radiator off and repairing minor leaks or valve faults at £100 to £150.
When there is no leak to be found
Sometimes every joint is dry and the pressure still falls. Then one of two things is going on.
The leak is hidden. Pipes under a ground floor or buried in a wall can lose water for months before any sign appears. A plumber can shut the valves under the boiler to separate it from the house pipework, then see which side loses pressure.
The fault is inside the boiler. Every sealed boiler has an expansion vessel, a small tank with a rubber diaphragm that takes up the swelling of the hot water. When it fails, the pressure shoots up as the heating warms, the safety valve lets water out through the outside pipe, and the gauge reads low again once everything cools. The tell-tale is a needle that swings from high to low between hot and cold.
Who to ring for which
- Leak on a radiator, valve or pipe: a plumber.
- Leak under a floor: a plumber, who may need to lift boards.
- Outside pipe dripping, needle swinging high and low, or a code that keeps coming back: a Gas Safe registered engineer, if the boiler burns gas. Those faults are behind the casing, and by law only a registered engineer may work there.
- Not sure: describe what you see in the form. The right person will be clear from the description.
For a sense of cost, a UK emergency plumber guide lists loss of boiler pressure at an average labour charge of £180 for 30 to 60 minutes' work on an urgent call. A visit booked for a weekday should have no call-out premium on it.
Why leaving it costs more
It is tempting to live with it. Two minutes at the filling loop and the heating is back.
The snag is what fresh water does. The water in a healthy system is old and has lost its dissolved air, so it barely rusts the steel. Each top-up brings in new, airy water and the rusting starts again. That rust turns to sludge, the sludge blocks radiators and wears the pump, and a cheap leak becomes a dear repair.
And the water you keep adding has not vanished. It is in your floor.
Common questions
Can low boiler pressure damage the boiler?
Low pressure on its own mostly just stops the boiler working, which is the safety switch doing its job. The harm comes from the cause and the cure: a leak wetting the house, and repeated top-ups feeding rust into the system. Fix the reason and the gauge looks after itself.
My boiler has no pressure gauge. Does this apply to me?
Probably not. Older systems are fed from a small tank in the loft and are open to the air, so they have no gauge and no filling loop. If radiators on a system like that go cold upstairs, the loft tank may have run dry because its float valve has stuck. A plumber can sort that.
Find the leak instead of topping up
Every time the needle drops and you bring it back up, a little more water has gone into the fabric of the house and a little more rust has started in the radiators. The fault is nearly always cheaper to mend than the damage it does if left.
Say how often the pressure drops, what you found on your leak hunt and where in Workington you are. No charge is made for asking.